top of page

Lift Arm Pivot Pins and Bushings: The Wear Point Behind a Sloppy Skid Steer

Nov 9
6 min read

A skid steer that's developed a little play in the lift arms doesn't feel broken at first. It feels loose — a slight clunk when the arms shift direction, a bit of side-to-side wobble with the bucket extended, nothing dramatic enough to stop work over. That looseness has a name: pin and bushing wear at the lift arm pivot points, and it's one of the most universal wear items on any skid steer or compact track loader, regardless of brand. Left unaddressed, it doesn't just stay annoying — it gets progressively worse, and the pins and bushings aren't the only things that eventually pay the price for it.


Bobcat skid steer lift arm replacement part

Where the Wear Actually Happens


Every pivot point on a lift arm — where the arm meets the loader frame, where the lift cylinder connects to the arm, and where the bucket or attachment tilts — relies on a steel pin running through a bushing pressed into the mating part. The bushing is the sacrificial wear surface, deliberately softer than the pin so that it wears out first and can be replaced without machining the frame or the arm itself. Under constant load reversals — lifting, lowering, tilting, lifting again, hundreds of times a day — that bushing material slowly wears away, opening up clearance between the pin and the bore. That clearance is the "slop" operators feel.


How to Actually Check for It


Checking pivot wear properly means watching the joint while it moves, not just looking at it sitting still. With the machine running and the arms raised partway, have someone gently work the arms up and down and side to side while you watch each pivot point closely for visible movement between the pin and its housing. A small amount of play is normal and expected on any machine with hours on it. What you're watching for is play that's grown noticeably since the last check, or play that's uneven — one pivot looser than its mirror-image counterpart on the other arm — since that usually means one side is wearing faster and should move up the repair priority list.


Why Ignoring It Costs More Than the Pins and Bushings


The real argument for catching pivot wear early isn't the cost of the pins and bushings themselves, which are inexpensive wear items by design. It's what happens to the parts around them if the clearance is allowed to grow unchecked. A pin running loose in a worn bore starts to hammer against the bore surface under load instead of rotating smoothly within it, and that hammering action can gradually wear an out-of-round or egg-shaped bore into the arm or frame casting itself — a repair that's considerably more involved than swapping a pin and bushing, since it can mean welding, boring, and re-machining the housing rather than just replacing a wear part.


Bobcat lift arm assembly for skid steer and track loaders

Vertical-Lift vs. Radial-Lift: Why Some Machines Feel Looser Than Others


It's worth knowing that vertical-lift loaders, which use a more complex multi-link arm geometry to keep the bucket closer to the machine through the full lift path, naturally have more pivot points than a simpler radial-lift design — which means more total wear surfaces and, often, a bit more inherent side-to-side play even when every pivot is in good condition. That's not a defect; it's a tradeoff for the better reach and visibility a vertical-lift path provides. The practical takeaway is not to panic over play on a vertical-lift machine that would be alarming on a radial-lift one — compare each machine's current play against its own baseline when it was new or freshly serviced, rather than against a different lift geometry entirely.


Grease Intervals Are Doing More Work Than You Think


Of every maintenance item on a skid steer, grease frequency at the pivot points has probably the single biggest effect on how long pins and bushings actually last. Dry or under-greased pivots run metal against metal with no protective film between them, which accelerates wear dramatically compared to a properly greased joint. A daily or twice-daily greasing routine during heavy-use periods, following the manufacturer's recommended grease type and interval, is one of the cheapest and most effective ways to extend pivot life — and it's often the first thing to slip when a crew is busy and the walkaround gets rushed.


A Note on Compact Track Loaders vs. Wheeled Skid Steers


Lift arm pivot wear follows the same mechanism on a compact track loader as it does on a wheeled skid steer, since both typically share the same arm geometry within a given manufacturer's lineup — but a CTL's higher-flotation undercarriage and higher typical operating weight can put slightly different stress patterns through the arms depending on the work being done. A CTL doing heavy grading on soft ground tends to load the arms more evenly across a wider range of motion, while a wheeled skid steer working concrete or asphalt surfaces may see more impact loading on the pivots from faster, harder-surface operation. Neither pattern is inherently worse for pivot life — they're just different enough that the inspection habit matters equally on both, rather than assuming one platform is somehow exempt from the wear the other clearly shows.


When It's Time to Call a Dealer Instead of Handling It Yourself


A straightforward pin and bushing swap, caught early with the bore still round and undamaged, is well within reach of a shop with basic equipment and the right service manual. The calculation changes once a bore has started to wear out of round, or once a pivot pin has seized in its bushing and resists normal removal — at that point, forcing the issue with improvised tools risks turning a routine repair into a damaged casting that genuinely does need dealer-level machining capability. Knowing the difference between "this is a normal wear-part swap" and "this needs a dealer's attention" before starting the job saves a lot of wasted shop time and prevents a bad situation from getting worse.


Bobcat, Caterpillar, and Kubota: Parts and Access Compared


Bobcat's dealer network stocks lift arm pins and bushings as standard, readily available parts across both its Classic and Pro skid steer lineups, with the manufacturer's own parts shop listing exact replacement pins and arm assemblies by model. Caterpillar's skid steer and CTL lineup follows a similar pattern through its dealer network, with ground-engaging and pivot wear parts typically stocked at the dealer level rather than needing special order. Kubota's compact track loaders, built on a chassis platform shared in part with other compact equipment in its lineup, generally see solid parts turnaround through the combined construction-and-agricultural dealer network Kubota operates, which can be an advantage in more rural service areas.


Related Reading on Skid Steer Wear and Design


Pivot wear is one piece of a skid steer's overall maintenance picture. Our breakdown of flat-face vs. ball-and-sleeve attachment couplers covers another high-wear connection point on the same machine, and our guide to the 5-minute daily walkaround across Bobcat, CAT, and Kubota is a good companion piece for building pivot checks into a routine that's actually sustainable day to day.


Financing a Skid Steer That's Earning Its Wear


Pivot wear is a sign of a machine being used, not a sign something's gone wrong — but a skid steer racking up enough hours to need regular pin and bushing attention is also a skid steer that's proven its value to your operation. If that machine is getting close to the point where repair costs start competing with the economics of an upgrade, or if you're adding a second machine to keep up with demand, BFC Equipment Loans structures financing and leasing around how a skid steer actually gets used. For Bobcat-specific financing programs, visit our Bobcat skid steer equipment financing page.


Bottom Line


A little play in the lift arms is normal wear, not a crisis — but it's worth tracking over time, greasing aggressively, and repairing before loose pins start damaging the bores they ride in. Catch it at the pin-and-bushing stage and it's a routine, inexpensive fix. Ignore it long enough and it becomes a frame or arm repair instead.


Ready to Move Forward?


Comments


bottom of page