top of page

Ground Pressure and Flotation: Why a Track Loader Can Work Ground a Skid Steer Can't

Nov 4
6 min read

Put a wheeled skid steer and a compact track loader side by side on a dry gravel lot and they'll both look like they're doing the same job fine. Drive either one onto a wet lawn, a soft spring job site, or freshly graded fill, and the difference becomes obvious fast. Ground pressure, how much weight each square inch of the machine's footprint actually transmits into the ground, is the real physics behind that difference, and it's worth understanding in real numbers rather than just the marketing phrase "low ground pressure."


Ground Pressure Is a Simple Ratio With Big Consequences

Ground pressure is just the machine's operating weight divided by the total ground contact area of its tires or tracks, usually expressed in pounds per square inch. A wheeled skid steer concentrates its entire weight onto four relatively small tire contact patches. A tracked machine of comparable weight spreads that same weight across two long, continuous track footprints, which is a dramatically larger total contact area. The result is that a compact track loader can often run ground pressures in the 4 to 6 PSI range, while a similarly sized wheeled skid steer frequently sits well above that, sometimes north of 10 PSI depending on tire width and inflation. That gap is exactly why a CTL can work ground a wheeled machine would simply sink into.



Why Wheeled Skid Steers Still Win on Hard Surfaces

None of this makes the wheeled skid steer the wrong choice generally, it makes it the wrong choice for soft, wet, or sensitive ground specifically. On pavement, concrete, compacted gravel, or any hard surface where sinking isn't a risk, a wheeled machine's advantages come right back to the front: tires are cheaper to buy and replace than an undercarriage and track system, they transmit less rolling resistance on hard surfaces so the machine can move faster between tasks, and tire wear from regular pavement and concrete work is a far smaller, more predictable cost than track and undercarriage wear from the same duty cycle. A demolition, concrete, or hardscape contractor working almost exclusively on hard surfaces is paying for traction and flotation capability a wheeled machine will genuinely never need.


Why Tracked Machines Win on Soft Ground

A compact track loader's lower ground pressure isn't just about avoiding getting stuck, it actively protects the ground itself, which matters on jobs where the client cares about turf, landscaping, or a finished grade that a wheeled machine's tire ruts would visibly damage. Landscaping, turf installation, residential yard work, and site work on recently placed fill or wet clay all favor a CTL specifically because the lower ground pressure lets the machine keep working, and keep the ground looking acceptable, in conditions that would have a wheeled skid steer spinning, rutting, or simply stuck.



Flotation Is the Real Word for What's Actually Happening

"Flotation" is the industry term for a machine's ability to stay on top of soft ground rather than sinking into it, and it's a direct function of ground pressure relative to the bearing capacity of whatever surface the machine is on. Soil with a low bearing capacity, wet clay, loose sand, uncompacted fill, needs a correspondingly low ground pressure to avoid sinking, which is exactly the scenario where a track loader's wider footprint earns its keep. On soil with a reasonably high bearing capacity, well-compacted base material, most of this advantage simply isn't needed, because the ground can support either machine's weight without either one sinking in the first place.


What Track Width and Tire Width Actually Change

Within each category, width matters as much as the wheels-versus-tracks decision itself. A wider track reduces ground pressure further for the same operating weight, which is exactly why some manufacturers offer multiple track width options on the same base machine, a narrower track for maneuverability in tight spaces, a wider track specifically for flotation on genuinely soft ground. The same logic applies to tires on a wheeled machine: wider, lower-pressure flotation tires reduce ground pressure compared to narrower, higher-pressure standard tires, though even the widest flotation tire on a wheeled skid steer typically won't match a comparable CTL's total ground contact area.


The Maintenance Side of the Trade-Off

The ground-pressure advantage a track loader offers comes with a real ongoing cost most buyers underestimate until they've owned one for a few years. An undercarriage, tracks, rollers, idlers, drive sprockets, is a more expensive system to maintain and eventually replace than a set of tires, and track tension needs regular checking since running too loose or too tight accelerates wear on exactly the components that make flotation possible in the first place. A wheeled machine's tires are a simpler, cheaper, and more universally available wear item, which is part of why total cost of ownership on a CTL doing mostly hard-surface work can actually run higher than the wheeled alternative, even though the CTL cost more to buy in the first place.


Making the Call for Your Actual Ground

The honest way to decide isn't brand loyalty or whichever machine the dealer has in stock, it's an honest look at what percentage of your actual working days happen on soft, wet, or sensitive ground versus hard, consistent surfaces. A contractor running 80 percent hardscape and demolition work with the occasional soft-ground job is usually better served financially by a wheeled machine, accepting that the rare soft-ground job might need extra caution or a rental track machine for that one task. A landscaping, turf, or residential site contractor running soft ground most days is better served owning the track machine outright and accepting the higher undercarriage maintenance cost as the real price of a machine that can actually finish the jobs a wheeled unit would get stuck on.


Speed and Ride Are Part of the Real Comparison Too

Ground pressure isn't the only operational difference worth weighing. A wheeled skid steer generally travels faster between tasks on a hard, open site, since tires simply roll with less resistance than tracks on pavement or compacted gravel, which matters on a job where the machine spends real time driving between work areas rather than digging in one spot. A tracked machine tends to ride smoother over rough or rutted ground because the longer track footprint bridges over small depressions and bumps that a wheeled machine's tires would transmit directly into the cab, which some operators running all-day shifts on rough sites genuinely notice by the end of a long week. Neither advantage shows up on a spec sheet the way ground pressure or rated operating capacity does, but both are real enough to ask about on a demo before committing to either platform for years of daily use.


Attachment Compatibility Rarely Decides This

It's worth clearing up a common misconception directly: most hydraulic attachments, buckets, forks, augers, brooms, work identically well on a wheeled skid steer and a comparably sized compact track loader, since the attachment interfaces and hydraulic flow specs are standardized across a manufacturer's lineup regardless of undercarriage type. Attachment compatibility is almost never the deciding factor between wheels and tracks, which means buyers can safely make the ground-pressure decision on its own merits without worrying it will lock them out of attachments they already own or plan to buy.


Resale Value Follows Regional Demand

Resale value on either platform tracks regional demand more than any universal rule. In markets with a lot of landscaping, turf, and residential site work, used compact track loaders tend to hold value well because local buyers specifically want the flotation. In markets dominated by commercial concrete, demolition, and hardscape work, used wheeled skid steers often resell just as strongly, because that buyer pool never needed the track advantage in the first place and isn't willing to pay a premium for a capability that wasn't going to get used. Knowing your local used-equipment market, not just the national averages, is worth a conversation with a dealer before assuming one platform is automatically the safer long-term investment.


A Mixed Fleet Solves This for a Growing Operation

For a contractor whose work genuinely spans both hard-surface and soft-ground jobs in meaningful volume, the real answer is often not choosing one platform exclusively but building toward a small mixed fleet, a wheeled machine for the hardscape and demolition jobs, a track machine dispatched specifically to the landscaping and soft-ground work. That's a bigger financing conversation than a single-machine purchase, but it's a legitimate growth path once volume on both job types justifies carrying two machines instead of compromising on one, and it's worth discussing openly with a lender rather than defaulting to whichever single machine seems like the safer first purchase.


Related Reading

For how a CTL's undercarriage itself is built, see our breakdown of rigid, roller, and torsion undercarriage designs. To understand the lift-capacity numbers on either machine's spec sheet, read rated operating capacity vs. tipping load explained, and see BFC's full skid steer and track loader financing hub for financing on either configuration.


Ready to Put This Equipment to Work?

BFC Equipment Loans provides equipment financing and leasing for startups and existing businesses nationwide, with approval paths for strong credit and for borrowers who've been turned down elsewhere. Whatever you decide on the machine, here's how to move forward with BFC.

Comments


bottom of page